A how-to guide from Unclog.itWritten by a Red Seal plumber in British Columbia

10 to 30 minutes · Easy to moderate · Updated November 2026

How to unclog a shower drain.

The complete guide from a professional plumber. Pull the hair first, plunger second, hand snake third, and a clear point where you stop and call a pro.

A plastic hair strip pulling a hair clog out of a shower drain

Standing in water right now?

1. Turn the shower off. More water won't push it through.

2. No drain cleaner. It sits in the water you then have to work in.

3. Check the toilet and sink. If they are slow too, it isn't the shower. See why.

Steps 1 to 5

Get set up.

  1. Rubber gloves, safety glasses, a flashlight, a screwdriver, a bucket and a plastic hair strip

    Step 1

    Gear up

    Put on rubber gloves and eye protection. Have a flashlight, a screwdriver, a bucket and a few paper towels within reach.

    Andrew's pro tip: What comes out of a shower drain is hair held together with old soap. Gloves make the job a lot easier to finish.

  2. A shower head turned off above a shower floor with standing water

    Step 2

    Turn the water off

    Stop the shower and leave it off. If the water is over the drain, bail it into the bucket and tip it into a toilet or sink that is draining normally.

    Andrew's pro tip: Don't keep running water to "push it through". It only gives you more to bail.

  3. A bottle of chemical drain cleaner, crossed out, beside a shower with standing water

    Step 3

    Check for drain cleaner

    If chemical drain cleaner has gone down this drain, stop here. Don't plunge it, don't open it and don't put your hands in the water.

    Andrew's pro tip: Drain cleaner sitting on top of a clog is still drain cleaner. What to do if you already poured it.

  4. A screwdriver undoing the screw in a shower drain cover, and the cover lifting off

    Step 4

    Take the cover off

    Most covers are held by one or two screws. Others snap in and pry up with a flat screwdriver, or lift straight out. Put the screws somewhere they can't roll into the drain.

    Andrew's pro tip: Lay a cloth over the open drain while you deal with the screws. A screw in the trap is a second clog. How each kind of cover comes off.

  5. Long-nose pliers lifting a wad of hair out of the open drain, with the cover set to one side

    Step 5

    Pull out what you can see

    Shine the flashlight in. Most shower clogs sit right under the cover, caught on the crossbars. Lift the hair out with long-nose pliers or a gloved finger and put it in the garbage, not the toilet.

    Andrew's pro tip: About half the time, this is the whole job. Run the shower for a minute. If it drains, skip to step 9.

Steps 6 to 8

Work down the drain.

Start with a plastic hair strip. If the shower is still slow, plunge it. If that doesn't clear it, move on to a hand snake. Each tool reaches further than the one before.

Step 6: use a plastic hair strip

A flat plastic strip with barbs along the edges. It costs a few dollars at any hardware store and clears most shower clogs on its own.

  1. A plastic hair strip being pushed down into the open drain

    Hair strip · 1 of 4

    Feed the strip straight down the drain, barbs first, past the crossbars.

  2. The strip pushed down until it stops, then worked up and down so the barbs catch the hair

    Hair strip · 2 of 4

    Push until it stops at the bend of the trap, then work it up and down a few centimetres so the barbs catch the hair.

    Andrew's pro tip: Don't spin it in full turns and don't force it round the bend. A cheap strip can snap, and then the strip is the clog.

  3. The strip pulled slowly back out with a wad of hair caught on the barbs

    Hair strip · 3 of 4

    Pull it back out slowly. The barbs bring the hair up with them.

  4. Hair going in the garbage and the strip going back down the drain for another pass

    Hair strip · 4 of 4

    Wipe the hair off into the garbage and go again. Three or four passes, until the strip comes up clean.

    Andrew's pro tip: Bring it up slowly through the opening, or the hair wipes off on the crossbars and drops back in.

Step 7: use a plunger

A plunger moves what the strip couldn't reach, in the trap itself. Skip this step completely if any drain cleaner has gone in.

  1. A flat cup plunger, the right one for a shower, beside a toilet plunger with a flange, crossed out

    Plunger · 1 of 5

    Use a flat cup plunger. A toilet plunger has a flange folded down from the cup and won't seal on a flat floor. If yours has one, tuck it up inside.

  2. A cup plunger set over the drain with enough water on the floor to cover the rim of the cup

    Plunger · 2 of 5

    Set the cup over the drain with the cover off. You want about 2 to 3 cm of water on the floor, enough to cover the rim of the cup. Add some from the tap if you need to.

    Andrew's pro tip: Air compresses and water doesn't. A cup full of water pushes on the clog; a cup full of air just bounces.

  3. A wet cloth held over the bathtub overflow plate while the drain is plunged

    Plunger · 3 of 5

    In a bathtub, hold a wet cloth tight over the overflow plate first. Without it, the plunger pushes air out through the overflow and nothing reaches the clog.

  4. The plunger worked up and down in firm strokes with the cup kept sealed to the floor

    Plunger · 4 of 5

    Give it about a dozen firm strokes, straight up and down, keeping the cup sealed to the floor.

    Andrew's pro tip: The pull does as much as the push. You're rocking the clog loose, not hammering it down the pipe.

  5. The plunger lifted away and the standing water draining

    Plunger · 5 of 5

    Lift the plunger away and watch. If the water drops, run the shower to check. If nothing has changed after two rounds, stop and move on to the snake.

Step 8: use a hand snake

A hand snake goes round the trap and brings the clog back with it. It is the same idea as the drain machine a plumber uses, at a smaller size.

  1. A hand drain snake: a drum that holds a quarter-inch cable, with a crank on the front and a bulb head on the end of the cable

    Hand snake · 1 of 7

    Use a hand snake with a 1/4 inch cable, sometimes sold as a drum auger. Not a toilet auger, which is too short and too stiff for this bend.

  2. The snake cable pushed down the drain by hand until it stops at the bend of the trap

    Hand snake · 2 of 7

    Loosen the thumbscrew and push the cable down the drain by hand until it stops. That first stop is the bend of the trap, not the clog.

  3. The drum held a hand-width above the drain and the thumbscrew tightened to lock the cable

    Hand snake · 3 of 7

    Slide the drum down until it is about a hand's width above the drain, then tighten the thumbscrew to lock the cable.

    Andrew's pro tip: Keep that gap short. A long loop of loose cable between the drum and the drain is what kinks.

  4. The crank turned clockwise while the cable is pushed gently through the bend of the trap

    Hand snake · 4 of 7

    Turn the crank clockwise with steady, gentle pressure. The cable works its way round the bend. Loosen, feed another hand's width, lock, and crank again.

    Andrew's pro tip: Always clockwise, going in and coming out. Backwards unwinds the cable and it tangles in the pipe.

  5. The head of the cable turning into the hair clog in the trap

    Hand snake · 5 of 7

    When it gets harder to turn and feels springy, you are in the hair. Give it a few more turns so the head winds into it. Don't force it.

  6. The cable wound back out of the drain with the hair wrapped around its head

    Hand snake · 6 of 7

    Keep turning clockwise as you pull the cable back out, wiping it with a rag as it comes. The hair comes up wrapped round the head.

    Andrew's pro tip: Have the bucket beside the drain. What comes up is black and it drips.

  7. A drain snake fed through the bathtub overflow opening, down the overflow pipe and round the trap

    Hand snake · 7 of 7

    In a bathtub, go in through the overflow, not the drain. Take off the overflow plate and feed the cable down that pipe. It drops straight to the trap.

    Andrew's pro tip: The drain opening leads into a tight bend under the tub that a cable won't turn. The bathtub steps in full.

Step 9

Test it and put the cover back.

  1. The shower running and the water going straight down the drain

    Run it for five minutes

    Run hot tap water at full flow for three to five minutes. A drain that is really clear takes everything the shower head gives it, with no water building up on the floor.

    Andrew's pro tip: A quick splash proves nothing. A half-cleared drain keeps up for thirty seconds and then backs up.

  2. The drain cover back on with a domed hair catcher sitting over it

    Refit the cover, add a hair catcher

    Screw or press the cover back on. Then put a hair catcher over it and empty it after every shower. It is the cheapest plumbing repair you will ever buy.

    Andrew's pro tip: Snug is enough on the screws. Overtighten them and you strip the plastic drain body they thread into.

A shower floor with deep standing water that will not drain

Final check

Still clogged? Unclog.it.

If the snake didn't clear it, the blockage is past the trap, something solid is lodged in it, or the pipe itself is the problem. That's a job for a licensed plumber with a drain machine.

A plumber clears a shower drain from $329 in regular hours (9 to 5, Monday to Friday). After hours, prices double.

Metro Vancouver and the Fraser Valley, British Columbia

Before you keep going

Shower or sewer line?

A shower is often the lowest drain in the house, so it is the first place a blocked main line shows up. A strip, a plunger and a hand snake only reach a clog in the shower's own drain. These signs point to the main sewer line instead:

  • Water comes up in the shower when you flush the toilet or run a sink
  • The toilet or a sink is slow at the same time
  • The shower gurgles when another fixture drains
  • The water that comes up is dirty, or smells of sewage

That's a different job, and nothing you do at the shower will fix it. Stop running water in the house until it's cleared. In Metro Vancouver and the Fraser Valley, Unclog.it clears a main sewer line from $769 in regular hours.

Shower over a bathtub

Tub with a shower? Two things change.

The drain end of a bathtub, seen from the sideA cutaway drawing showing the stopper, the drain shoe under the tub, the overflow plate, the overflow pipe, the tee where the two meet, the trap and the trap arm.1234567

A bathtub has a stopper where a shower has a cover, and it has an overflow: the plate on the end wall of the tub, with a pipe behind it that joins the drain under the tub.

  1. Stopper. Hair wraps around it and under it. It has to come out before anything else.
  2. Drain shoe. The bend under the tub. Too tight for a snake to turn.
  3. Overflow plate. Cover it with a wet cloth when you plunge.
  4. Overflow pipe. The straight way down. This is where the snake goes in.
  5. Tee. Where the drain and the overflow meet.
  6. Trap. The same bend a shower has, and where the rest of the hair sits.
  7. Trap arm. On to the rest of the house.

The bathtub steps in full

Why the tools work

Inside a shower drain.

Under a shower floor, seen from the sideA cutaway drawing showing the drain cover, the drain body, hair caught under the cover, the trap with a clog in it, the water the trap holds, the trap arm, the vent and the pipe to the rest of the house.12345678

Under the cover, the drain drops into a U-shaped bend called the trap. The trap always holds water, and that water is what keeps sewer gas out of the bathroom. Hair catches in two places: on the crossbars right under the cover, and in the bottom of the trap. A strip reaches the first. A plunger and a snake reach the second.

  1. Cover. Also called the strainer or grate. It keeps big things out and lets hair through.
  2. Drain body. The fitting set into the shower floor. The cover screws or snaps into it.
  3. Crossbars. Just under the cover. Most shower clogs start here.
  4. Trap. The bend. What gets past the crossbars settles in the bottom of it.
  5. Trap seal. The water the trap holds. If it dries out, the shower smells.
  6. Trap arm. The run from the trap to the vent, sloped to drain.
  7. Vent. A pipe up through the roof that lets air in behind the water, so the trap isn't sucked dry.
  8. Branch drain. On to the rest of the house's plumbing. A blockage here is not a shower clog.

Hair strip, plunger and snake compared.

Shower drain tools and what each is best for
ToolBest forWatch out for
Plastic hair stripHair under the cover and in the top of the drainCan snap if you twist or force it
Cup plungerSoft clogs sitting in the trapNever after drain cleaner. In a tub, cover the overflow
Hand snake, 1/4 inchHair in the trap and the pipe just past itKinks if you force it. Can mark an acrylic or fibreglass shower
Toilet augerToilets onlyToo short and too stiff for a shower trap
Chemical drain cleanerNothing in a blocked showerBurns skin and eyes, and makes every later step riskier

What to buy

A plastic hair strip. About 50 cm long with barbs along both edges. A few dollars, often sold in packs. They are cheap enough to throw out when they get grim.

A hand snake. A 1/4 inch cable, 4.5 to 7.5 m (15 to 25 ft) long, in an enclosed drum with a thumbscrew. Expect to pay $25 to $50. You don't need the drill-powered kind for a shower.

A cup plunger. The flat-bottomed kind made for sinks and tubs. About $10. Keep it separate from the toilet plunger.

A hair catcher. A dome or a flat mesh that sits over the drain, or a basket that drops into it. Whichever one you will actually empty.

No links and nothing to sell. Buy them wherever is closest.

More help and questions.

Short answers from a plumber. Tap a question to open it.

Why not baking soda and vinegar, or boiling water?

You'll find plenty of internet fixes for a slow shower. Here's what each one actually does:

  • Baking soda and vinegar: it fizzes, and that's all. The fizz is carbon dioxide and salty water. It doesn't dissolve hair.
  • Boiling water: plastic drain pipe is rated for about 60°C. Water straight off the boil can soften the pipe and the seal under the shower. Hot water from the tap is fine.
  • Bleach: it whitens the gunk and leaves the hair where it was. Never mix it with any other cleaner.
  • A wire coat hanger: it can hook hair near the top, but it scratches the shower and can't get round the trap. A plastic hair strip costs a few dollars and does the same job better.

Andrew's pro tip: If a hair strip, a plunger and a snake have not moved it, nothing in the kitchen cupboard will.

Is chemical drain cleaner safe in a shower?

No. It is made to sit on a clog, and in a blocked shower that means a floor full of caustic water that you then have to stand beside, plunge or bail. It can burn skin and eyes, and it makes the job harder and more expensive for whoever clears the drain next. More on drain cleaner, and what to do if it's already in there.

How do I stop the shower clogging again?
  • Fit a hair catcher over the drain and empty it after every shower.
  • Lift the cover every few weeks and pull out what has collected under it.
  • Brush long hair before the shower, not in it.
  • Don't rinse grout, thinset or paint buckets in the shower.
  • Run a shower you rarely use for a minute each month, so the trap stays full.
Why does my shower keep clogging?

Usually because the hair is being cleared from the top but not from the trap, so what's left catches the next lot. Other causes are soap scale narrowing an older pipe, grout or tile debris from a renovation, a small object lodged in the trap, or a drain that is too small for the shower. Seven causes and how to tell them apart.

Can I use a toilet plunger or a toilet auger on a shower?

A toilet plunger works only if you fold its flange up inside the cup, so the rim sits flat. Clean it first. A toilet auger is the wrong tool: it's about a metre long, stiff, and shaped for a toilet bowl. A shower needs a 1/4 inch hand snake.

How far down is a shower clog?

Nearly always within the first metre. The hair catches on the crossbars under the cover first, and what gets past them settles in the trap, the U-shaped bend a short way below the floor. If you have fed two or three metres of cable and nothing has changed, the problem is further into the house's piping and it's time to call a plumber.

Why does my shower drain smell?

A film of soap, skin and hair on the inside of the drain is the usual cause, and cleaning under the cover fixes it. In a shower that's rarely used, the water in the trap evaporates and lets sewer gas through. Run the water for a minute. Three smells and the fix for each.

When should I call a plumber?

Call a plumber if:

  • The strip, the plunger and the snake have not cleared it
  • Water comes up in the shower when you flush the toilet or run a sink
  • More than one drain in the house is slow
  • There's a water stain on the ceiling under the shower
  • Drain cleaner is sitting in the water
  • You're not comfortable going further

A plumber has a drain machine that reaches further and pulls harder than a hand snake, and a camera for what can't be seen.

What does it cost to have a shower drain cleared?

In Metro Vancouver and the Fraser Valley, Unclog.it clears a shower or bathtub drain from $329 in regular hours, 9 to 5, Monday to Friday. That covers up to 2 hours on site. After hours, every price is double. What the price includes.

Keep it handy

Print it, save it, share it.

One-page checklist

The nine steps and the stop-and-call signs on a single sheet, for the bathroom cupboard or a rental binder.

Open the printable checklist

The nine steps as one picture

Free to use on your own site or newsletter with a link back.

Open the infographic

More shower drain help

One question, one page.

Andrew Henderson

Meet the author

Andrew Henderson, Red Seal Plumber

Andrew has been clearing drains in Metro Vancouver and the Fraser Valley for more than 15 years. He founded Pure Mechanical Group, the company behind Unclog.it, and contributed to the Red Seal Occupational Standard, the national standard plumbing apprentices train to.

Legal disclaimer

The information on this site is provided for general educational purposes only and does not constitute professional advice. Plumbing work can cause property damage or personal injury if performed incorrectly. Proceed at your own risk. Always follow local codes and manufacturer instructions. If you are unsure at any time, stop and contact a licensed professional plumber.

Unclog.it and Pure Mechanical Group Ltd. make no warranties or guarantees and expressly disclaim liability for any loss, damage, or injury arising from the use of this content. By using this site you agree to these terms.